Zoning & Building Safety:

Advertisement


Zoning and Building Safety Department
Stormwater Management

Best Management Practices (BMPs)

The Stormwater Control Ordinance allows only clean stormwater to be discharged from your site. Sediment, fertilizers, yardwaste, metals, gravel, and all other pollutants cannot be released from your site. Below are some control measures with links to web pages with possible best management practices (BMPs) that you may want to use at your site. Please note there are many manufacturers out there, you are responsible for evaluating these products and choosing the ones you want to use. Please contact the manufactures to see if their product will work for your site. If you would like to add your company to this page send us an e-mail Click to send e-mail.

PERIMETER CONTROLS

Properties, waters (creeks, streams, wetlands, etc), drainage channels and ditches adjacent to the site shall be protected from deposit of sediment. This may be accomplished through the preservation of a well vegetated buffer strip around the lower perimeter of the land disturbance, by installing perimeter controls such as sediment barriers or sediment basins or dikes, or any combination of such measures. Here are some examples:


INLET PROTECTION

Municipalities around the country are increasing their use of catch basin inserts to treat stormwater before it enters surface waters. Part of the increase stems from requirements to meet federal and state regulations and part because it’s the right thing to do. The ability to capture trash, sediment, and pollutants such as oil, grease, and metals increases the quality of the environment for everyone.

A multitude of companies are manufacturing products for the catch basin filtration market. Whether your need is for sediment removal, mitigation of pollutants, or trash capture,  try these websites to find a product to meet your needs.


DUST CONTROL

Dust control BMPs reduce surface activities and air movement that causes dust to be generated from disturbed soil surfaces. Construction sites can generate large areas of soil disturbance and open space for wind to pick up dust particles. Limited research at construction sites has established an average dust emission rate of 1.2 tons/acre/month for active construction (WA Dept. of Ecology, 1992). Airborne particles pose a dual threat to the environment and human health. First, dust can be carried offsite, thereby increasing soil loss from the construction area and increasing the likelihood of sedimentation and water pollution. Second, blowing dust particles can contribute to respiratory health problems and create an inhospitable working environment.

Dust control measures are applicable to any construction site where there is the potential for air and water pollution from dust traveling across the landscape or through the air. Dust control measures are especially important in arid or semiarid regions, where soil can become extremely dry and vulnerable to transport by high winds. Implement dust control measures on all construction sites where there will be major soil disturbances or heavy equipment construction activity such as clearing, excavation, demolition, or excessive vehicle traffic. Earthmoving activities are the major source of dust from construction sites, but traffic and general disturbances can also be major contributors (WA Dept. of Ecology, 1992). The dust control measures that are implemented at a site will depend on the topography and land cover of the site and its soil characteristics and expected rainfall.

When designing a dust control plan for a site, the amount of soil exposed will dictate the quantity of dust generation and transport. Therefore, construction sequencing and disturbing only small areas at a time can greatly reduce problematic dust from a site. If land must be disturbed, consider using temporary stabilization measures before disturbance. A number of methods can be used to control dust from a site; not all will be applicable to a site. The owner, operator, and contractors responsible for dust control at a site will have to determine which practices accommodate their needs according to specific site and weather conditions.


Back to top


VEHICLE TRACKING

Vehicle tracking is a temporary construction entrance that is typically a stone pad located where vehicles leave a construction site. The purpose of the stone pad is to provide an area where mud can be removed from tires before a vehicle leaves the site. The stone pad consists of clean rock designed in such a way that vehicle tires will sink in slightly. This helps remove mud from the tires as the vehicle passes over the pad.

The effectiveness of temporary rock construction entrances for trapping sediment depends upon the length, depth of rock, frequency of use and maintenance, as well as the type of structure used. A newly installed rock construction entrance will be relatively effective. However, once the rock voids become clogged with mud, the practice will not serve its intended purpose until the rock is replaced. Include a wash rack where vehicle tires can be washed to increase effectiveness.


EROSION CONTROL

Erosion control is the practice of preventing or controlling wind or water erosion in agriculture, land development and construction. This usually involves the creation of some sort of physical barrier, such as vegetation or rock, to absorb some of the energy of the wind or water that is causing the erosion. Effective erosion controls are important techniques in preventing water pollution and soil loss. They are often implemented in conjunction with sediment controls such as sediment basins and silt fences.

 

Back to top



Rock Island County Office Building (map ExternalLink.gif)
1504 Third Avenue, Room 305, Rock Island IL 61204-8624
Phone: (309) 558-3771      Fax: (309) 786-4456

      Hours: 7:00 AM to 10:00 AM and 3:00 PM to 4:30 PM - Monday thru Friday
Inspectors are in the field from 9:30 AM until 3:00 PM